SE SE4400-PAIR Factory Matched Pair of SE4400 Large Diaphragm Condenser Microphones TGF33

Mint, Perfect, Open Box with Full sE Electronics Warranty

Classic versatility at its finest! Hand-crafted with the highest attention to detail, built with a roadworthy die-cast all-metal housing, metal switches, and rugged spring steel wire mesh grille that can take a beating during day-to-day tour life. The sE4400 Matched Pair appeals with its down-to-earth elegance, offering discrete electronics prioritizing the features you really need.

Features

• Hand-crafted true condenser capsule individually tuned in our own factory
• Classic vintage sound and all-metal housing
• Switchable pickup patterns, cardioid, omnidirectional, figure-eight, and hypercardioid
• Innovative close-miking shockmount
  40 / 80 Hz bass-cut filters and -10 / -20 dB pads

TUNED & SONICALLY MATCHED IN-HOUSE
Each sE4400 Matched-Pair is rigorously tested, tuned in-house and sonically matched to ensure a virtually identical frequency response for balanced, consistent sound. Complete with a metal mic case, stereo bar, two shockmounts and two sE4400 microphones.

CUSTOM SHOCKMOUNT + CHASSIS
The flat, round-edged chassis design and custom suspension mount allow the mic to be centered within the shock, used flat against a drum head or guitar cab, among many other use cases, and provides exceptional protection from low-end rumble and footfall noise.

HAND-CRAFTED 1" TRUE CONDENSER CAPSULE
Individually tuned and cared for by sE’s skilled technicians, each sE4400’s hand-crafted, gold-sputtered, dual-diaphragm capsule captures sound sources of all kinds with breathtaking clarity and precision, be it in demanding studio or fast-paced live environments.

FREE OF THRILLS, NO LEDs. NO PLASTIC SWITCHES.
Select between 4 polar patterns with metal switches, from cardioid to omnidirectional or figure-eight to hypercardioid, with a gold-sputtered, dual-diaphragm capsule for precision-based miking techniques to minimize signal bleed from unwanted sources in demanding studio or fast-paced live environments.

DENT-PROOF METAL HOUSING & PREMIUM FINISH
Hand-crafted with the highest attention to detail, built with a roadworthy die-cast all-metal housing, metal switches, and rugged spring steel wire mesh grille, the sE4400 is built to last for years of demanding studio use and the day-to-day life of a touring artist.

SWITCHABLE PRE ATTENUATION PAD & BASS-CUT FILTER
Select between two pre-attenuation pads for an extended dynamic range and compensate for loud vocals, guitars, drums, and brass instruments. With two low-cut filters, easily tame excessive low-frequency rumble and proximity effect and efficiently adjust for close-miking techniques.

Recommended Use
Lead vocals, orchestral + strings, drums, overheads, electric guitar cab, piano, acoustic guitar, woodwinds, brass

Specifications

What's in the sE4400 Matched-Pair box
- sE4400 microphone (x2)
- Custom shock-mount + thread adapter (x2)
- Stereo mounting bar
- Metal case

Components
- Capsule: Hand-crafted 1" Gold-sputtered True Condenser
- Diaphragm: Gold-sputtered mylar

Power
- Electrical impedance: 22 Ohms
- Connectivity: 3-pin male XLR connector
- Powering: 48V Phantom Power (P48 according to IEC 61938)

Sound
- Polar patterns: Cardioid, Hypercardioid, Omni-directional, Figure-8
- Frequency range: 20 Hz - 20 kHz
- Sensitivity: 25 mV / Pa (-32 dBV)
- Max SPL: 137 / 147 / 157 dB (0/10/20 dB Attenuation pad - 0.5% THD)
- Equivalent noise level: 13 dB(A)
- Signal to noise ratio: 81 dB
- Low-cut filter: 40 / 80 Hz, 6 dB/Oct, switchable
- Attenuation pad: 10 / 20 dB, switchable

Dimensions
- Mic weight: 290 g (10.23 oz.)
- Mic length: 146 mm (5.75 in.)
- Mic width: 58 mm (2.32 in.)
- Mic diameter: 29 mm (1.10 in.)